MULTILAYER COATINGS Ti/TiN, Cr/CrN AND W/WN DEPOSITED BY MAGNETRON SPUTTERING FOR IMPROVEMENT OF ADHESION TO BASE MATERIALS

Authors

  • Jakub Horník CTU in Prague Faculty of. Mechanical engineering
  • Stanislav Krum CTU in Prague Faculty of. Mechanical engineering
  • David Tondl CTU in Prague Faculty of. Mechanical engineering
  • Maxim Puchnin CTU in Prague Faculty of. Mechanical engineering
  • Pavel Sachr CTU in Prague Faculty of. Mechanical engineering
  • Ladislav Cvrček CTU in Prague Faculty of. Mechanical engineering

DOI:

https://doi.org/10.14311/AP.2015.55.0388

Keywords:

PVD coatings, magnetron sputtering, tool steel, adhesion, nanoindentation

Abstract

The paper deals with evaluation of single and multilayer layer PVD coatings based on Cr and Ti widely used in tool application. Additionally, W and WN based coating which are not so widespread were designed and deposited as functionally graded material. The coatings properties were evaluated from the point of view of hardness and adhesion. The hardness measuring was carried out using nanoindentation method. The scratch test was performed to test adhesion. Moreover, the presence of metallic interlayer in functionally graded materials further increases the coating adhesion by gradually approaching its composition to the substrate. Coatings consisting of W and WN have showed very good adhesion. With regard to the results of the scratch test, the multilayer coatings of CrN, TiN and WN have increased adhesion and can be assumed to have their protective function improved. Results will be appliedin development of functionally graded layers for functionally graded materials.

Downloads

Download data is not yet available.

Author Biographies

  • Jakub Horník, CTU in Prague Faculty of. Mechanical engineering

    Department of materials engineering

    Material diagnostic - metallography electron microscopy

  • Stanislav Krum, CTU in Prague Faculty of. Mechanical engineering

    Department of materials engineering

    Material diagnostic - metallography electron microscopy

  • David Tondl, CTU in Prague Faculty of. Mechanical engineering

    Department of materials engineering

    Material diagnostic - metallography electron microscopy

  • Maxim Puchnin, CTU in Prague Faculty of. Mechanical engineering

    Department of materials engineering

    Material diagnostic and electron microscopy

  • Pavel Sachr, CTU in Prague Faculty of. Mechanical engineering

    Department of materials engineering

    Diagnostic materials and coatings  

  • Ladislav Cvrček, CTU in Prague Faculty of. Mechanical engineering

    Department of materials engineering

    Diagnostic materials and coatings  

Downloads

Published

2015-12-31

Issue

Vol. 55 No. 6 (2015)

Section

Articles

License

Authors who publish with this journal agree to the following terms:

1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.

2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.

3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).

4. ddd

How to Cite

Horník, J., Krum, S., Tondl, D., Puchnin, M., Sachr, P., & Cvrček, L. (2015). MULTILAYER COATINGS Ti/TiN, Cr/CrN AND W/WN DEPOSITED BY MAGNETRON SPUTTERING FOR IMPROVEMENT OF ADHESION TO BASE MATERIALS. Acta Polytechnica, 55(6), 388-392. https://doi.org/10.14311/AP.2015.55.0388